Datasheets | Transistors | IGBTs | IGBTs, 600V

6 A, 600 V hyper fast IGBT

Datasheet

Format: (641 kb)

Last Updated: 21/08/2009

Pages: 18

Raw Ascii Text- ( Hide )
(Unformatted textual content of the document used by search engines)

STGBL6NC60DI, STGDL6NC60DI STGFL6NC60DI, STGPL6NC60DI
6 A, 600 V hyper fast IGBT
Features

Low CRES / CIES ratio (no cross-conduction susceptibility) Very high frequency operation
1 3 2

3 1 2

Very soft ultrafast recovery antiparallel diode

TO-220FP

TO-220

Applications

High frequency inverters SMPS and PFC (hard switching too) High frequency motor drive
3 1

3 1

DPAK

D²PAK

Description
Thanks to a new lifetime control system, this new PowerMESHTM technology-based series of devices exhibits very low turn-off energy, representing the best trade-off between on-state voltage and switching losses and thus allowing very high operating frequencies. Figure 1. Internal schematic diagram

Table 1.

Device summary
Marking GBL6NC60DI GDL6NC60DI GPL6NC60DI GFL6NC60DI Package D²PAK DPAK TO-220 TO-220FP Packaging Tape and reel Tape and reel Tube Tube

Order codes STGBL6NC60DIT4 STGDL6NC60DIT4 STGPL6NC60DI STGFL6NC60DI

August 2009

Doc ID 15536 Rev 2

1/18
www.st.com 18

Contents

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

Contents
1 2 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Electrical characteristics (curves) . . .. . .. . .. . .. . ..... 6

3 4 5 6

Test circuits

. . .. . .. . .. . .. . .. . .. . .. . .. . ... 9

Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2/18

Doc ID 15536 Rev 2

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

Electrical ratings

1

Electrical ratings
Table 2.
Symbol

Absolute maximum ratings
Value Parameter DPAK TO-220 D²PAK 600 13 5 14 6 18 18 20 10 25 50 -56 - 55 to 150 22 2500 7 3 Unit TO-220FP V A A A A V A A W V C

VCES IC IC
(1) (1) (2)

Collector-emitter voltage (VGE = 0) Collector current (continuous) at TC = 25 C Collector current (continuous) at TC = 100 C Turn-off latching current Pulsed collector current Gate-emitter voltage Diode RMS forward current at TC = 25 C Surge non repetitive forward current tp=10ms sinusoidal Total dissipation at TC = 25 C Isolation withstand voltage (RMS) from all three leads to external heat sink (t=1 s; TC=25 C) Operating junction temperature

ICL

ICP(3) VGE IF IFSM PTOT VISO Tj

1. Calculated according to the iterative formula:

Tj ( m x ) T I C ( T C ) = -------------------------------------------------a---------------C--------------------------------------R t h j c × V C E ( s a t ) ( m a x ) ( T j ( m a x ), I C ( T C ) )

2. Vclamp = 80%,(VCES), Tj =150C, RG = 10 , VGE = 15 V 3. Pulse width limited by maximum junction temperature and turn-off within RBSOA

Table 3.
Symbol

Thermal data
Value Parameter DPAK Thermal resistance junction-case IGBT max. 2.5 4.5 100 TO-220 D²PAK 2.2 4 62.5 Unit TO-220FP 5.6 7 C/W C/W C/W

Rthj-case Rthj-amb

Thermal resistance junction-case diode max. Thermal resistance junction-ambient max.

Doc ID 15536 Rev 2

3/18

Electrical characteristics

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

2

Electrical characteristics
(Tj=25 C unless otherwise specified) Table 4.
Symbol

Static electrical characteristics
Parameter Test conditions Min. Typ. Max. Unit

Collector-emitter V(BR)CES breakdown voltage (VGE = 0) VCE(sat) VGE(th) ICES IGES gfs

IC = 1 mA

600 1.9 2.2 2 3.75

V V V V V A mA nA S

VGE = 15 V, IC= 1.5 A Collector-emitter saturation VGE = 15 V, IC= 3 A voltage VGE= 15 V, IC= 3 A,Tj=125C Gate threshold voltage Collector cut-off current (VGE = 0) Gate-emitter leakage current (VCE = 0) Forward transconductance VCE= VGE, IC= 250 A VCE = 600 V VCE = 600 V, Tj= 125 C VGE = 20 V VCE = 15 V, IC= 3 A

2.9 5.75 50 5 100

3

Table 5.
Symbol Cies Coes Cres Qg Qge Qgc

Dynamic electrical characteristics
Parameter Input capacitance Output capacitance Reverse transfer capacitance Total gate charge Gate-emitter charge Gate-collector charge Test conditions Min. Typ. Max. 208 32.5 5.4 12 2.6 4.9 Unit pF pF pF nC nC nC

VCE = 25 V, f = 1 MHz, VGE = 0 VCE = 390 V, IC = 3 A, VGE = 15 V (see Figure 17)

-

-

-

-

4/18

Doc ID 15536 Rev 2

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

Electrical characteristics

Table 6.
Symbol td(on) tr (di/dt)on td(on) tr (di/dt)on tr(Voff) td(off) tf tr(Voff) td(off) tf

Switching on/off (inductive load)
Parameter Turn-on delay time Current rise time Turn-on current slope Turn-on delay time Current rise time Turn-on current slope Off voltage rise time Turn-off delay time Current fall time Off voltage rise time Turn-off delay time Current fall time Test conditions VCC = 390 V, IC = 3 A , RG= 10 VGE = 15 V (see Figure 18) VCC = 390 V, IC = 3 A , RG = 10 VGE = 15 V, Tj =125 C (see Figure 18) VCC = 390 V, IC = 3 A, , RGE = 10 VGE = 15 V (see Figure 18) VCC = 390 V, IC = 3 A, , RGE = 10 VGE =15 V, Tj = 125 C (see Figure 18) Min. Typ. 6.7 3.7 930 6.5 4 820 17 46 47 35 67 55 Max. Unit ns ns A/s ns ns A/s ns ns ns ns ns ns

-

-

-

-

-

-

-

-

Table 7.
Symbol Eon (1) Eoff(2) Ets Eon (1) Eoff(2) Ets
1.

Switching energy (inductive load)
Parameter Turn-on switching losses Turn-off switching losses Total switching losses Turn-on switching losses Turn-off switching losses Total switching losses Test conditions VCC = 390 V, IC = 3 A RG = 10 VGE=15 V , (see Figure 18) VCC = 390 V, IC = 3 A , RG = 10 VGE = 15 V, Tj = 125 C (see Figure 18) Min. Typ. 32 24 56 51 46 97 Max. Unit J J J J J J

-

-

-

-

Eon is the turn-on losses when a typical diode is used in the test circuit in (see Figure 19). If the IGBT is offered in a package with a co-pak diode, the co-pack diode is used as external diode. IGBTs and diode are at the same temperature (25C and 125C)

2. Turn-off losses include also the tail of the collector current

Table 8.
Symbol

Collector-emitter diode
Parameter Test conditions IF = 1 A IF = 3 A IF = 3 A, Tj=125 C IF = 3 A, VR = 40 V, di/dt = 100 A/s (see Figure 19) IF = 3 A,VR = 40 V, Tj =125 C, di/dt = 100 A/s (see Figure 19) Min. Typ. Max. 1.7 1.8 1.3 23 21 1.5 47 51 2 Unit V V V ns nC A ns nC A

VF t rr Qrr I rr m t rr Qrr I rr m

Forward on-voltage Reverse recovery time Reverse recovery charge Reverse recovery current Reverse recovery time Reverse recovery charge Reverse recovery current

-

-

Doc ID 15536 Rev 2

5/18

Electrical characteristics

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

2.1
Figure 2.

Electrical characteristics (curves)
Output characteristics Figure 3. Transfer characteristics

Figure 4.

Transconductance

Figure 5.

Collector-emitter on voltage vs temperature

Figure 6.

Gate charge vs gate-source voltage Figure 7.

Capacitance variations

6/18

Doc ID 15536 Rev 2

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI Figure 8. Normalized gate threshold voltage vs temperature Figure 9.

Electrical characteristics

Collector-emitter on voltage vs collector current

Figure 10. Normalized breakdown voltage vs temperature

Figure 11. Switching losses vs temperature
E (J) 50
AM03825v1

Eon

40 Eoff 30

20

VCC = 390 V, VGE = 15 V IC = 3 A, RG = 10 0 25 50 75 100 TJ(C)

10

Figure 12. Switching losses vs gate resistance Figure 13. Switching losses vs collector current
E (J)
AM03826v1

VCC = 390 V, VGE = 15 V IC = 3 A, Tj = 125 C

E (J) 50 40 Eon

AM03827v1

100 Eoff

80 Eon

30 20

60 Eoff 10 0 0.5 VCC = 390 V, VGE = 15 V Rg = 10 , Tj = 125 C 1 1.5 2 2.5 3 Ic(A)

40

0

40

80

120

160

RG()

Doc ID 15536 Rev 2

7/18

Electrical characteristics Figure 14. RBSOA

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI Figure 15. Forward voltage drop versus forward current
IFM(A)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0
Tj=125C (maximum values) Tj=25C (maximum values) Tj=125C (typical values)

VFM(V)
1 2 3 4 5

8/18

Doc ID 15536 Rev 2

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

Test circuits

3

Test circuits
Figure 17. Gate charge test circuit

Figure 16. Test circuit for inductive load switching

Figure 18. Switching waveform

Figure 19. Diode recovery time waveform

Doc ID 15536 Rev 2

9/18

Package mechanical data

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

4

Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark.

10/18

Doc ID 15536 Rev 2

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

Package mechanical data

TO-220 type A mechanical data

mm Dim Min A b b1 c D D1 E e e1 F H1 J1 L L1 L20 L30 P Q 4.40 0.61 1.14 0.48 15.25 1.27 10 2.40 4.95 1.23 6.20 2.40 13 3.50 16.40 28.90 3.75 2.65 3.85 2.95 10.40 2.70 5.15 1.32 6.60 2.72 14 3.93 Typ Max 4.60 0.88 1.70 0.70 15.75

0015988_Rev_S

Doc ID 15536 Rev 2

11/18

Package mechanical data

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

TO-220FP mechanical data mm Dim. Min.
A B D E F F1 F2 G G1 H L2 L3 L4 L5 L6 L7 Dia 28.6 9.8 2.9 15.9 9 3 4.4 2.5 2.5 0.45 0.75 1.15 1.15 4.95 2.4 10 16 30.6 10.6 3.6 16.4 9.3 3.2

Typ.

Max.
4.6 2.7 2.75 0.7 1 1.70 1.5 5.2 2.7 10.4

L7 E A

B Dia L6 L5 F1 F2 F D

H G1

G

L2 L 3

L4 7012510_Rev_J

12/18

Doc ID 15536 Rev 2

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

Package mechanical data

TO-252 (DPAK) mechanical data
DIM. A A1 A2 b b4 c c2 D D1 E E1 e e1 H L L1 L2 L4 R V2 0o 0.60 0. 20 8o 4.40 9.35 1 2. 80 0. 80 1 6.40 4. 70 2. 28 4.60 10.10 mm. min. 2.20 0.90 0.03 0.64 5.20 0.45 0.48 6.00 5. 10 6.60 typ max. 2.40 1.10 0.23 0.90 5.40 0.60 0.60 6.20

0068772_G

Doc ID 15536 Rev 2

13/18

Package mechanical data

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

D²PAK (TO-263) mechanical data

mm Dim Min A A1 b b2 c c2 D D1 E E1 e e1 H J1 L L1 L2 R V2 4.40 0.03 0.70 1.14 0.45 1.23 8.95 7.50 10 8.50 2.54 4.88 15 2.49 2.29 1.27 1.30 0.4 0 8 0 5.28 15.85 2.69 2.79 1.40 1.75 0.192 0.590 0.099 0.090 0.05 0.051 Typ Max 4.60 0.23 0.93 1.70 0.60 1.36 9.35 10.40 Min 0.173 0.001 0.027 0.045 0.017 0.048 0.352 0.295 0.394 0.334

inch Typ Max 0.181 0.009 0.037 0.067 0.024 0.053 0.368 0.409 0.1 0.208 0.624 0.106 0.110 0.055 0.069 0.016 8

0079457_M

14/18

Doc ID 15536 Rev 2

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

Packaging mechanical data

5

Packaging mechanical data

DPAK FOOTPRINT

All dimensions are in millimeters

TAPE AND REEL SHIPMENT
REEL MECHANICAL DATA
DIM. A B C D G N T 1. 5 12.8 20.2 16.4 50 22. 4 18. 4 13. 2 mm MIN. MAX . 330 0. 059 0.504 0.520 0. 795 0.645 0.724 1. 968 0.881 BULK QTY 2500 i n ch MIN. MAX. 12. 992

TAPE MECHANICAL DATA
DIM. A0 B0 B1 D D1 E F K0 P0 P1 P2 R
W

BASE QTY 2500

mm MIN. 6. 8 10.4 1. 5 1. 5 1.65 7. 4 2.55 3. 9 7. 9 1. 9 40
15.7 16.3

inch MIN. MAX . 7 0.267 0.275 0.409 0.417 0.476 0.059 0.063 0. 059 0.065 0.073 0.291 0.299 0.100 0.108 0.153 0.161 0.311 0.319 0.075 0.082 1. 574
0.618 0.641

MAX . 10. 6 12. 1 1.6 1. 85 7.6 2. 75 4.1 8.1 2.1

Doc ID 15536 Rev 2

15/18

Packaging mechanical data

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

D2PAK FOOTPRINT

TAPE AND REEL SHIPMENT
REEL MECHANICAL DATA
DIM. A B C D G N T 1. 5 12.8 20.2 24.4 100 30. 4 26. 4 13. 2 mm MIN. MAX . 330 0. 059 0.504 0.520 0795 0.960 1.039 3. 937 1.197 BULK QTY 1000 i n ch MIN. MAX. 12. 992

TAPE MECHANICAL DATA
DIM. A0 B0 D D1 E F K0 P0 P1 P2 R T W mm MI N. 10. 5 15. 7 1.5 1. 59 1. 65 11.4 4.8 3.9 11.9 1.9 50 0. 25 23. 7 24.3 MAX. 10.7 15.9 1. 6 1.61 1.85 11.6 5. 0 4. 1 12.1 2. 1 i n ch MI N. MAX. 0.413 0.421 0.618 0.626 0.059 0.063 0.062 0.063 0.065 0.073 0.449 0.456 0.189 0.197 0.153 0.161 0.468 0.476 0.075 0.082 1.574 0.35 0.0098 0.0137 0.933 0.956

BASE QTY 1000

* on sales type

16/18

Doc ID 15536 Rev 2

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

Revision history

6

Revision history
Table 9.
Date 27-Mar-2009 13-Aug-2009

Document revision history
Revision 1 2 First release Document status promoted from preliminary data to datasheet, inserted Section 2.1: Electrical characteristics (curves), updated TO-220 and TO-220FP package mechanical data Changes

Doc ID 15536 Rev 2

17/18

STGBL6NC60DI, STGDL6NC60DI, STGPL6NC60DI, STGFL6NC60DI

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com

18/18

Doc ID 15536 Rev 2

Document Number: 15536

Untitled Document

Further Information
Contact Online Support (Registration Required)



All rights reserved © 2010 STMicroelectronics :: Terms Of Use :: Privacy Policy